A drive sprocket is the toothed undercarriage wheel that engages the track links and drives the machine forward, and catalog reference 20Y-27-11581 is one commonly quoted reference for a segmented drive sprocket on a 20-ton-class hydraulic excavator. It sits at the final drive output, where the travel motor turns the sprocket and its teeth pull the track chain around the undercarriage. Its job is simple to describe and critical in effect: transmit travel torque into the chain, keep the track engaged under load, and do it for thousands of hours in mud, rock and abrasive dust. If you are reading this because the teeth look hooked or worn, because the machine tracks poorly or clatters at speed, or because you are planning an undercarriage overhaul and want to know which sprocket to fit, the short answer is: inspect tooth wear against the limit, confirm the reference, tooth count and segment pattern against the old unit, and replace the sprocket as part of a matched undercarriage set rather than against worn neighbours. This guide explains what the drive sprocket does, how to read a reference such as 20Y-27-11581, how sprockets wear, the symptoms of a worn or wrong unit, how to choose a replacement, and how to change it without shortening the life of a new chain. The reference is used only as a representative catalog number for this class of part; no equipment or component brand is named.
Why does this part attract so much search demand? Because the drive sprocket is a wear item in the highest-cost system on the machine, and undercarriage demand grows with fleet age and working severity. Industry data puts undercarriage at more than half of an excavator’s full-life maintenance spend, and search interest in sprockets, rollers and track chains rose sharply in recent seasons as mines, quarries and construction fleets entered overhaul cycles. A sprocket is rarely searched in isolation: buyers pair the part name with the reference, the tooth count and the segment pattern, because a segmented sprocket that looks correct in a photograph can have the wrong pitch or bolt pattern for the chain it must drive. A search for a specific sprocket reference is almost never idle browsing. It is a signal that a machine is down for undercarriage work, that periodic tooth measurement has reached the wear limit, or that a parts buyer is verifying a cross reference before committing to an order. This guide is written for that buyer: the owner, fleet manager, technician or parts buyer who wants the correct sprocket, a clear diagnosis and a replacement that protects the chain it meshes with.
What a Drive Sprocket Is and What It Does
The Final Drive Output and the Track Engagement Point
A drive sprocket is the toothed wheel at the end of the travel drive that transfers rotation into linear movement of the track chain. On a 20-ton-class hydraulic excavator the travel motor and reduction gearbox turn a hub, and the sprocket bolted or splined to that hub carries teeth that seat into the gaps between the chain links and pins. As the sprocket rotates, each tooth pushes on a link pin and advances the chain, which rolls over the track rollers and idler to move the machine. This is why the drive sprocket is called the driving wheel while rollers and idlers are followers: it is the only undercarriage wheel that applies torque to the chain. Getting this interface right matters because the sprocket and chain form a matched gear set; the tooth profile is cut to the pitch of the chain, and any mismatch concentrates load on a few teeth and links instead of spreading it across the whole engagement arc.
Most excavator drive sprockets of this class are built as a segmented rim rather than a one-piece wheel. A segmented sprocket is made of separate toothed segments bolted around a hub or rim. The arrangement has two practical advantages: a worn segment can be rotated or replaced without discarding the whole wheel, and the segments can be forged or cast from a wear-resistant alloy and heat treated independently of the hub. On a 20-ton-class machine a common layout uses several bolted segments forming a complete ring of teeth, with each segment carrying two or three teeth. Segment construction also lets the sprocket be shipped and handled in pieces, which reduces weight and cost. When inspecting a segmented sprocket, the bolts and their locking method deserve as much attention as the tooth profile, because a loose segment changes the pitch and quickly damages a new chain.
Why the Reference 20Y-27-11581 Matters
A catalog reference such as 20Y-27-11581 is not a decorative label. It identifies a specific combination of tooth count, chain pitch, segment pattern, bolt-hole layout, hub interface, material and heat-treatment condition for one undercarriage application. A sprocket cut for the wrong pitch will not seat cleanly into the chain links, so it will climb, skip and wear both parts rapidly. A segment ring with the wrong bolt pattern will not mount on the final drive hub, and a hub with the wrong spline or offset will change the track alignment. Even where two sprockets look nearly identical from a distance, small differences in tooth form, hardness depth and pitch tolerance change how quickly the teeth wear and how smoothly the chain runs. The reference is the anchor that lets a supplier confirm all of these details before dispatch. Read it from the old part, the service record or the machine’s parts list, quote it in full including any suffix, and do not rely on a photograph alone.
Searches for a specific sprocket reference carry a practical meaning that is easy to miss. The same machine model can be built with more than one undercarriage configuration across production batches and markets, and chain pitch or segment count can differ between them. A supplier who ships by description alone will frequently send a wheel that is technically an excavator sprocket but functionally the wrong one: correct diameter but wrong tooth count, or a segment pattern that fits the hub but not the chain currently fitted. Treating the full reference as the specification, rather than as a loose hint, is what separates a same-day repair from a week of returns and freight claims. It is also the anchor for the parts normally handled alongside a sprocket: the track chain, the track rollers, the carrier rollers and the idlers. A buyer who quotes the full reference can plan the whole undercarriage service in one order, which is almost always cheaper than discovering a worn chain after a new sprocket has been fitted.
Materials, Hardness and What the Numbers Mean
Alloy Steel and Surface Hardening
The reference class represented by 20Y-27-11581 is typically produced from a medium-carbon alloy steel such as 50Mn or a comparable grade, selected for a balance of core toughness and surface wear resistance. After forming, the teeth are hardened so the working surfaces resist abrasion while the body of the segment remains tough enough to absorb impact without cracking. Published figures for this class place surface hardness broadly in the HRC 48 to 58 range, with a hardened layer extending several millimetres below the surface, and impact values in the tens of joules at room temperature. These are representative ranges rather than a single guaranteed value, because different manufacturers tune the heat treatment to their own process, but they explain what to ask about when comparing a replacement: the steel grade, the hardness range, the depth of the hardened layer and the heat-treatment route of normalising, quenching and tempering.
Why does hardness depth matter as much as the surface reading? Because a sprocket tooth is a wearing part with a finite reserve. A very hard skin over a soft core can give an impressive initial reading but collapse under load as the hardened layer is worn through and the softer material underneath deforms. A well-processed tooth keeps a consistent hardness for several millimetres, so as the tip wears the exposed surface is still resistant. This is why a buyer should treat a quoted HRC number as meaningful only alongside a depth specification and a stated material grade. The same reasoning applies to the segment bolts and the hub interface: the teeth may be hardened while the fasteners are specified to a different, tougher standard, and mixing fasteners of an unknown grade during assembly is a common cause of loose segments in service.
Specification Snapshot
The table below collects the representative data most often checked when sourcing a segmented drive sprocket of this class. Treat it as a specification checklist to confirm against the part being offered and the machine being serviced, not as a substitute for the manufacturer’s drawing.
| Attribute | Representative value | Why it matters |
|---|---|---|
| Catalog reference | 20Y-27-11581 (representative) | Anchors tooth count, pitch, bolt pattern and hub interface |
| Application class | 20-ton-class hydraulic excavator | Defines load and chain size |
| Construction | Segmented rim, bolted tooth segments | Allows segment rotation and replacement |
| Material | 50Mn / 45SiMn-class alloy steel | Balances surface wear with core toughness |
| Surface hardness | Approximately HRC 48-58 | Resists tooth abrasion under load |
| Hardened depth | Roughly 4-10 mm | Sets usable wear reserve before the soft core shows |
| Impact value | About 8-25 J at room temperature | Indicates resistance to shock loading |
| Heat treatment | Normalising, quenching and tempering | Produces the specified hardness profile |
| Normal service life | Up to about 4000 hours in moderate duty | Shortens sharply in abrasive ground |
| Warranty commonly quoted | About two thousand hours | Useful benchmark when comparing suppliers |
| Inspection method | Tooth profile gauge and segment bolt torque check | Catches wear before the chain is damaged |
| Replacement practice | Match with chain condition, replace as a set | Protects new parts from accelerated wear |
How a Drive Sprocket Wears and How to Spot It
The Typical Wear Pattern
A sprocket does not usually fail suddenly. It wears gradually at the tooth flanks and tips where the chain pins roll in and out of engagement. In abrasive material the hardened surface is slowly removed, the tooth becomes thinner and more pointed, and the space between teeth widens as the profile changes. The classic sign is a hooked or sharpened tooth shape when viewed from the side, compared with the square, even profile of a new segment. Wear is rarely uniform around the ring: the segments that spend more time loaded by travel direction and machine posture can show deeper wear, which is why rotating segments on a service interval is a common practice. The second wear site is the bolted interface, where repeated load can loosen fasteners and allow a segment to shift, changing the pitch and accelerating damage to both sprocket and chain.
Wear matters because of the relationship between the sprocket and the chain. As tooth profiles wear, engagement becomes less precise, the chain tends to climb the teeth, and vibration and noise increase. A worn sprocket fitted to a new chain will rapidly lengthen and damage that chain, while a new sprocket fitted to a stretched chain will wear out prematurely because the pitch no longer matches. This is why undercarriage specialists talk about a matched set rather than single parts. Measuring the tooth profile at scheduled intervals, recording the readings and comparing them with the service limit lets a fleet plan the replacement during a known downtime window instead of reacting to a failure in the field.
Symptoms of a Worn or Incorrect Sprocket
Several field signs point to a sprocket problem. A rhythmic clack or clicking that rises with travel speed often means teeth are skipping or the chain is climbing due to a changed profile. Visible pointed or hooked teeth, uneven wear between segments, or metal shavings around the final drive area all suggest the engagement surfaces are worn. A machine that pulls to one side, tracks unevenly or loses drive under load may have a sprocket interface problem combined with track tension or roller wear. After fitting a replacement, persistent noise or rapid tooth wear usually indicates a pitch mismatch, a loose segment or a chain that was already beyond its service limit. In every situation the correct response is to stop and inspect rather than continue working, because the sprocket and chain destroy each other quickly once the geometry is wrong.
Careful diagnosis also rules out look-alike causes. Track noise can come from dry or seized rollers, an out-of-range track tension, a bent track frame or an idler that no longer turns freely, and replacing a sprocket will not cure any of these. Track tension is especially important: a chain that is too loose whips and climbs the sprocket, while one that is too tight pulls hard on the teeth and the final drive bearing. Before condemning the sprocket, check tension against the machine’s specification, spin the rollers and idler to confirm they turn freely, and look for debris packed between the segments. A systematic check avoids spending money on a part that was not the cause and protects a new sprocket from being fitted into a damaged system.
Choosing the Correct Replacement Sprocket
Reference, Pitch, Segment Pattern and Hub
Start the selection process with the reference from the old unit or the service record, and use 20Y-27-11581 as the representative example of how a reference anchors the choice. Confirm four things before ordering: the tooth count and chain pitch, the number and arrangement of bolted segments, the bolt-hole pattern and fastener grade, and the hub interface including spline, pilot diameter and offset. Any one of these being wrong can make an otherwise well-made sprocket unusable or destructive. If the machine has a mixed fleet history or a chain that was replaced under a different reference, measure the chain pitch and count the teeth on the fitted sprocket rather than assuming the catalog number on the parts list still applies. A short conversation with the supplier about these four points prevents most wrong-part orders.
Then compare the build quality. Ask which steel grade is used, what hardness range and hardened depth are specified, how the segments are heat treated, and what the quoted service life and warranty are. Examine the tooth profile and the finish of the flanks, and check that bolt holes are cleanly machined and evenly spaced. For a segmented wheel, confirm that the correct bolts and locking devices are supplied, because reusing stretched or worn fasteners is a false economy. A reputable supplier will state the reference clearly, offer the cross-reference list, and be willing to discuss the machine model and serial range before shipping. A seller who cannot answer basic questions about pitch, hardness and segment pattern is a risk on a part that works against a chain worth several times more.
Replacement Practice That Protects the Chain
Fit the sprocket as part of an undercarriage assessment rather than as an isolated swap. Inspect the chain for elongation and stiff links, check the rollers and idler for free rotation and leak-free seals, and set the track tension to specification after assembly. If the chain is close to its wear limit, replacing it together with the sprocket is usually cheaper over the next service interval than fitting a new wheel to a stretched chain. When fitting a segmented sprocket, clean the hub mating faces, fit new fasteners of the specified grade, tighten to the stated torque in a cross pattern, and use the locking method recommended for the application. Recheck bolt torque after the first hours of operation, because early settling is normal and a loose segment changes pitch immediately.
After replacement, run the machine at low speed for a short period and listen for irregular engagement noise. Recheck track tension once the chain has seated, and inspect the segment bolts again at the first service interval. Record the new sprocket reference, the date, the hour reading and the condition of the chain in the maintenance log, so the next inspection has a baseline. Fleets that keep these records find that sprocket life becomes predictable: the same duty cycle produces a similar wear rate, and replacement can be scheduled with other undercarriage work. That predictability is the real value of treating the drive sprocket as a measured, documented wear item rather than an emergency purchase.
Frequently Asked Questions About Drive Sprockets
What does a drive sprocket do on an excavator?
It converts the rotation of the final drive into movement of the track chain. Its teeth engage the chain links and push the track around the rollers and idler, so it is the driving wheel of the undercarriage while the other wheels follow.
What does reference 20Y-27-11581 identify?
It is a representative catalog reference for a segmented drive sprocket used on a 20-ton-class hydraulic excavator. The number anchors tooth count, chain pitch, segment layout, bolt pattern, hub interface and material specification for that application.
How long does an excavator drive sprocket last?
Service life depends heavily on the ground. In moderate duty a sprocket of this class can approach roughly 4000 hours, while abrasive rock, mud and overload shorten life substantially. Many suppliers quote a warranty near the two-thousand-hour mark as a benchmark.
What hardness should a replacement sprocket have?
Surface hardness for this class is commonly quoted around HRC 48 to 58 with a hardened layer several millimetres deep. Ask for the steel grade, hardness range and hardened depth together, because surface hardness alone does not predict wear life.
Why is the sprocket made in segments?
A segmented rim allows individual worn segments to be rotated or replaced without discarding the whole wheel, and lets the toothed segments be forged and heat treated for wear while the hub stays tough. It also reduces handling weight.
Can I fit a new sprocket to an old chain?
Only if the chain is within its wear limit. A stretched or stiff chain has the wrong pitch and will wear a new sprocket quickly, while a worn sprocket will damage a new chain. Undercarriage parts are best replaced as a matched set.
What are the signs of a worn sprocket?
Hooked or pointed teeth, uneven wear between segments, a rhythmic clicking that rises with speed, the chain climbing the teeth, and metal debris near the final drive. Compare the tooth profile with a new segment and check the fasteners.
How do I check whether a sprocket fits my machine?
Confirm the reference, then verify tooth count and pitch, segment pattern, bolt-hole layout and hub interface against the old unit. If the machine has a mixed service history, measure the chain pitch and count the teeth rather than relying on a parts list alone.
Should I replace sprockets and rollers together?
Not always, but they should be assessed together. If rollers, idlers or the chain are near their limits, replacing them with the sprocket protects the investment and prevents one worn component from accelerating wear on the new ones.
How often should sprocket bolts be checked?
Check torque after the first hours of operation following fitment and at each scheduled undercarriage inspection. Loose segments change the tooth pitch and can damage a new chain quickly, so they deserve the same attention as tooth wear.
Does track tension affect sprocket life?
Yes. A loose chain whips and climbs the teeth, while an over-tight chain loads the teeth and final drive bearing. Setting tension to the machine’s specification after any undercarriage work is one of the cheapest ways to extend sprocket life.
Cost, Downtime and Why the Reference Pays for Itself
Reading the Total Cost Rather Than the Sticker Price
The purchase price of a drive sprocket is only one part of what the part costs over its life. The larger costs are the downtime while the machine is out of service, the labour to open the final drive and fit the segments, and the risk to the chain and rollers if the new wheel is wrong or fitted badly. A cheaper sprocket with an unstated steel grade, no hardness depth and no clear reference can cost far more than a properly specified one if it wears out early or fails to mesh with the chain. Conversely, a correctly referenced sprocket fitted with new fasteners at the right torque, into a chain that is still within its limit, will usually reach its expected hours without attention. When comparing quotes, weigh the stated reference, material, hardness, warranty and supplier support alongside the price, and remember that a same-day decision made on price alone is the one most likely to turn into a repeat teardown.
Planning Around Scheduled Downtime
Because sprocket wear is gradual and measurable, it fits naturally into a planned maintenance window. Record tooth profile readings at each undercarriage inspection, note the hour count, and estimate how many hours remain before the service limit. That estimate lets a fleet order the correct reference in advance, group the sprocket with any chain or roller work due at the same time, and schedule the labour when the machine is already available. Planned replacement is consistently cheaper than emergency replacement: the part arrives before it is needed, the workshop is prepared, and there is no rush that leads to a wrong reference or a skipped torque check. Over a full service life, that discipline is what turns the drive sprocket from an unpredictable expense into a controlled, budgetable item on the undercarriage plan.
Planning the Undercarriage Service
The drive sprocket is a small part of the machine’s mass but a large part of its undercarriage cost and reliability. Treated as a measured wear item, it becomes predictable: the reference fixes the specification, the tooth profile tells you when replacement is due, and a matched set protects the chain and rollers around it. Treated as an emergency purchase, it becomes expensive, because a wrong pitch, a loose segment or a worn chain can destroy a new wheel in a fraction of its expected life. The practical plan is straightforward. Quote the full reference such as 20Y-27-11581, confirm pitch, segment pattern and hub interface, choose a sprocket with a stated steel grade and heat treatment, fit new fasteners to the specified torque, and record the work against the hour meter. Do that and the sprocket will do its job quietly for thousands of hours, converting drive torque into dependable movement while the rest of the undercarriage wears at its expected rate.

