The track chain, also called the track link assembly or crawler chain, is the single most-searched undercarriage wear part on a 20-ton-class hydraulic excavator, and catalog reference 20Y-32-00040 is one commonly quoted reference for a steel track link on this class of machine. A track chain is a loop of linked steel segments, each with a pin and a bushing, that runs around the front idler, the sprocket and the track rollers to carry the machine’s weight and provide traction. If you are reading this because your machine’s track is stretching, skipping over the sprocket, or has come off, the short answer is: measure the pitch elongation first, because that single number decides whether you need a new chain, a matched set, or something else entirely. This guide explains what the track chain does, how it wears, how to measure it in a few minutes, what the reference 20Y-32-00040 actually specifies, and how to choose and fit a replacement that restores correct track tension and protects the rest of the undercarriage. The reference is used only as a representative catalog number for this class of part; no equipment or component brand is named.
Why does this one part attract so much search demand? Because the track chain is the backbone of the whole undercarriage wear system, and almost every other undercarriage decision depends on its condition. Industry estimates put the undercarriage segment in the billions of dollars annually and growing, with replacement demand now accounting for the majority of the aftermarket as the average machine in service grows older. Within that segment, the individual track chain is searched more often than any other single wear part, and its search curve follows machine hours and abrasive ground conditions rather than the calendar. A chain search is rarely an idle browse: it is a signal that a fleet has moved onto rock or quarry work, that a machine has clocked enough hours for measurable stretch, or that a track has started to skip. Buyers increasingly pair the word chain with matched set, because they have learned the hard way that replacing one worn side or one worn component simply accelerates wear on the rest. This guide is written for that buyer: the owner, fleet manager or parts buyer who wants one correct, deliverable chain and a clear reason for choosing it.
What a Track Chain Is and What It Does
The Track Chain as the Backbone of the Undercarriage
A track chain is a series of steel links connected by pins and bushings to form a continuous loop around the undercarriage. On a 20-ton-class hydraulic excavator it runs at the bottom over the track rollers that carry the machine’s weight, rises at the front over the idler, returns along the top over the carrier rollers, and wraps the sprocket at the rear where the final drive pushes it forward. Each link carries a track shoe, bolted on, that spreads the machine’s weight over the ground and provides the grousers that bite into soil. The chain therefore does three jobs at once: it transfers machine weight to the ground through the shoes, it provides the traction for travel and steering, and it absorbs the shock loads generated by digging and travelling. Because it does all three while immersed in mud, grit and water, it is the most heavily worked component on the machine and the one whose condition governs the life of everything it touches.
Understanding the chain as a system rather than a single part is the key to a sound replacement decision. The pins rotate a little inside the bushings with every link that passes under the machine, and that microscopic movement is what wears them down over thousands of hours. As the pin and bushing wear, the distance between pin centres, called the pitch, grows longer. A longer pitch no longer seats cleanly on the sprocket teeth, so the chain climbs, skips and jumps under load, and the skipping then wears the sprocket and the rails still faster. Worn rollers or a worn idler compound the problem by letting the chain run unevenly. This is why a chain search should always trigger an inspection of the whole wear system, and why fitting a new chain onto badly worn rollers and sprockets wastes part of the investment: the new chain is ground into the same worn pattern within a few hundred hours.
Why the Reference 20Y-32-00040 Matters
A catalog reference such as 20Y-32-00040 is not a decorative label. It identifies one specific combination of pitch, link width, pin diameter, bushing type, shoe bolt pattern, number of links and heat-treatment specification for a particular machine configuration. A chain with the wrong pitch will not seat on the sprocket; one with the wrong link width will not run between the roller flanges; one with the wrong shoe bolt pattern will not accept the shoes you already have. Even where two chains look identical in a photograph, the internal construction may differ: a sealed and lubricated chain holds grease between pin and bushing and can extend internal wear life substantially, while a dry chain relies on external lubrication and needs more frequent attention. The reference is the anchor that lets a supplier confirm all of these details before dispatch. Read the number stamped or etched on the old link, check it against the machine’s parts record, and quote the full reference including any suffix, because a suffix change can select a completely different link series.
Searches for a specific reference also carry a practical meaning that is easy to miss. The same machine family can appear with more than one undercarriage option across production years and regions, and a supplier who ships by description alone will frequently send a chain that is technically a track chain but functionally the wrong one: a lighter-duty link for a smaller machine, a different pitch, or a shoe pattern from a previous configuration. Treating the full reference as the specification, rather than as a loose hint, is what separates a same-day fit from a week of returns and freight claims. It is also the anchor for the related items specified against the same undercarriage: the track shoes, the sprocket segments, the track rollers, the idler and the recoil spring. A buyer who quotes the full reference can plan the whole undercarriage repair in one order, which is almost always cheaper than discovering the second worn component after the first has been fitted.
Track Chain Specifications at a Glance
The figures below are typical ranges for steel track chains on 20-ton-class hydraulic excavators, given as planning guidance rather than universal values. Always confirm the exact dimensions and material grade against your machine’s parts record and the old link before ordering, because the correct figure for your serial number is the only one that matters for fitment.
| Attribute | Typical specification | Why it matters |
|---|---|---|
| Reference example | 20Y-32-00040 (steel track link) | Anchors pitch, width, pin and shoe pattern |
| Surface hardness | HRC 50-56, hardening depth 4-8 mm | Resists pin, bushing and rail wear |
| Link material | Alloy steel, e.g. 35MnB / 40Mn2 | Heat-treatment response and toughness |
| Sealing type | Sealed and lubricated (SAL) or dry | SAL extends internal pin and bushing life |
| Common pitch | 203 mm / 216 mm classes | Must match the sprocket tooth spacing |
| Replacement rule | 2-3% pitch elongation | Industry service limit for a chain set |
| Ordering unit | Matched left and right set | Keeps both sides tracking evenly |
How a Track Chain Wears, and the One Number That Decides
Pin and Bushing Wear Turns Into Pitch Elongation
A track chain looks like one solid part, but it is an assembly of link bodies, pins, bushings and, on larger designs, seals and centre guides. The pin sits inside the bushing and both are heat-treated so their surfaces can slide against each other under enormous load. Every hour the machine travels, the pin rotates slightly inside the bushing, and that movement grinds material away. As material is lost, the distance from one pin centre to the next grows. That growth is pitch elongation, and it is the only hard number that decides the chain’s fate. As a scale reference, one millimetre of pin wear plus one millimetre of bushing wear across a fifty-link chain adds roughly one hundred millimetres to the chain’s length. A chain that has stretched cannot be cured by new rollers, and new rollers fitted to a stretched chain will simply be worn into the same pattern. Diagnose the chain first, then decide about everything else.
Pitch elongation produces a predictable chain of symptoms. At low levels the machine works normally. As stretch approaches the service limit, the chain begins to climb and skip on the sprocket, particularly under load or on a turn, and the operator hears a rhythmic clacking that rises with travel speed. The sprocket teeth take on a hooked or pointed profile, the rail surfaces polish and groove, and the machine may track poorly or throw the track on a slope. Fuel consumption rises because a misaligned, stretched chain drags, and cycle times lengthen because the machine loses travel efficiency. Every one of these symptoms is downstream of the same measurement, which is why measuring pitch is the cheapest and most decisive check an owner can make. It takes about five minutes, needs only a tape measure and a marker, and gives a number that can be tracked over time.
The reason the industry fixes on pitch rather than on visible appearance is that stretch is cumulative and invisible until it is well advanced. A chain can look acceptable to the eye while having gained two percent in pitch, because spread over dozens of links the extra length per joint is only a fraction of a millimetre. By the time a chain visibly sags or climbs the sprocket, the internal wear has usually passed the point where any service action other than replacement is worthwhile. Measuring converts an invisible condition into a written number, and a written number can be compared against a limit and against last month’s reading. That is why the five-minute check is worth more than an experienced glance, and why fleet operators who record pitch at every service consistently replace chains during planned downtime while others replace them after a failure that also damages the sprocket and rails.
How to Measure Pitch Elongation in Five Minutes
Park the machine on firm, level ground, clean the mud and stone from the chain so the pin centres are visible, and set the track so it is neither over-tight nor slack. Mark the centre of one pin, then count a fixed number of joints along the chain, for example ten links, and mark the centre of that pin. Measure the distance between the two marks and divide by the number of joints to get the average actual pitch. Compare this with the standard pitch for your chain size, which is stamped or documented for the chain series, and calculate the stretch as a percentage. Repeat the measurement at several points around the chain, because uneven wear matters as much as average wear, and write the numbers down so the next service can show a trend. A ten-millimetre gain on a 203-millimetre pitch is close to five percent, well past any sensible limit. Record the result at every service interval and the trend will tell you when to budget for a chain, long before it fails.
Interpreting the number is straightforward. From zero to one percent elongation the chain is in normal wear: keep operating and keep measuring. From one to two percent it is approaching the limit: plan the replacement at the next scheduled shutdown and budget for it now. From two to three percent it has reached the service limit and should be replaced as a matched set on both sides. Above three percent it is past the limit and the machine should stop, because a chain in that condition is actively damaging the rails, sprockets and rollers. The two-to-three-percent band is the industry norm and sits inside most service manuals, but the exact figure depends on the machine class and the ground it works on, so confirm against the manual for your serial number before signing off the job. A disciplined measurement schedule converts an unplanned failure into a planned purchase, which is the single biggest cost saving available in undercarriage maintenance.
Frequently Asked Questions About Track Chains
When should a track chain be replaced?
Replace a steel track chain when pitch elongation reaches roughly two to three percent, when wear is clearly uneven along its length, or when one side has already been replaced without the other. Do not wait for the chain to skip badly or come off, because by then the sprockets and rails have taken damage that costs far more than the chain. The decision rests on the pitch measurement, not on how the track looks from a distance.
Can I replace one side of the track chain only?
It is possible to fit one side on its own, and some suppliers will sell a single side, but it is rarely good value. The two sides almost always have similar hours, so the side you keep is already part-worn and will stretch away from the new one. A matched pair keeps both sides tracking evenly and spreads the cost of one strip and one downtime window over a full service life. Replace as a set unless the machine is genuinely low-hour and one side was damaged by a single impact.
Will new rollers fix a stretched chain?
No. Worn rollers do not cause a stretched chain, and new rollers cannot fix one. A chain that has passed its pitch limit has permanently changed geometry at every joint, and it will wear new rollers into the same worn pattern very quickly. Measure the chain first. If the chain is within specification and the problem is rough running or visible flats on the rollers, then rollers are the correct repair. Getting this order wrong is one of the most expensive mistakes in undercarriage work.
What is the difference between a dry chain and a sealed and lubricated chain?
A dry chain has no seals between pin and bushing and relies on external lubrication, so it needs more frequent greasing and wears faster in abrasive conditions. A sealed and lubricated chain, often shortened to SAL, holds grease inside each joint and keeps dirt out, which can extend internal pin and bushing life substantially. SAL chains cost more up front and are the usual choice for machines working in sand, gravel or quarry. Confirm which type your reference specifies before ordering, because they are not interchangeable on the same application.
How long does a track chain last?
There is no single figure. On firm, well-drained ground with careful operation, a complete undercarriage can deliver several thousand operating hours; in abrasive sand, gravel or fill, life can fall to roughly a third to a half of that, with the difference showing up fastest on rollers and sprockets. The chain itself usually outlasts the rollers, which is why replacing worn rollers early protects the much more expensive chain. Track hours, ground conditions and operator style matter far more than the nominal rating on the box.
Can I rebuild a chain by replacing individual links?
Only in a narrow situation: a low-hour machine where one or two links were damaged by an impact and the rest of the chain measures within specification. That is a repair, not a life extension. If elongation is beyond the limit or uneven along the chain, individual new pins and links cannot restore the geometry of the whole loop, and the money is better spent on a matched set. Rebuilt chains can be a reasonable short-term choice on a machine being sold within a season, but they carry the same measurement rule.
A final point on measurement technique matters for accuracy. Always measure with the track in a relaxed state, because a tight track stretches the distance between pins and gives a falsely high reading, while a track piled in mud can hide stretch behind slack. Clean at least the section you are measuring, mark pin centres rather than shoe edges, and measure over ten links instead of one so small errors are divided down. Repeat the same measurement on both sides of the machine, because one side can wear faster if the operator turns frequently in one direction or works on a cambered surface. Record the date, the machine hours and the reading together, and the resulting log becomes a maintenance asset: it tells you the wear rate per hundred hours, lets you forecast the replacement window, and turns a future purchase into a line in the next budget rather than an emergency. None of this needs a workshop or a specialist tool, and it is the habit that separates a well-managed fleet from one that is permanently reacting to breakdowns.
Specifying and Fitting the Replacement Chain
What to Confirm Before You Order
Confirm five things before a chain is dispatched. First, the full catalog reference including any suffix, read from the old link and checked against the parts record. Second, the pitch and link width, because these must match the sprocket and the roller flanges exactly. Third, the shoe bolt pattern and whether the new chain is supplied with or without shoes. Fourth, the sealing type, sealed and lubricated or dry, matched to your ground conditions. Fifth, the number of links and the overall length for your undercarriage configuration. State all five in the enquiry with consistent units, and ask the supplier to confirm fitment against your machine’s serial number rather than against a general model description. A supplier who states the reference and the dimensions explicitly has checked the fit; one who offers a broad fitment claim has not. Ask also what material grade and heat-treatment depth are specified, because those details decide how the chain survives abrasive work.
Planning the whole order around the undercarriage is the smarter approach. A chain rarely fails in isolation, so inspect the sprocket segments, the track rollers, the idler and the recoil spring at the same time, and price them together before the machine is stripped. If the rollers are more than half worn, replacing them with the chain avoids paying a second strip later. If the sprocket teeth are hooked, new chain on an old sprocket will wear prematurely. Ordering everything in one shipment reduces freight, guarantees the parts are matched to the same configuration, and concentrates the downtime into a single planned window. It also lets you verify that both sides are supplied as a matched set with identical link counts, which is the condition for even tracking after fitting.
Fitting, Tensioning and the First Hours
Fit the chain with the machine on level ground and the track supported, following the manufacturer’s procedure for releasing the old tension through the grease valve before any pin is removed. Grease in the track adjuster is under high pressure, so open the valve slowly and keep clear of the line. Clean the mating faces, fit the shoes to the correct bolt pattern and torque them evenly, and set the initial tension to the sag figure in the operator’s manual rather than to what looks tight by eye. A new chain settles in during its first hours, so recheck the tension after a short running period and again at the next service. Record the starting pitch measurement so future services have a baseline. During the first shift, listen for skipping or uneven tracking and stop to investigate rather than continuing; early adjustment is cheap, while a new chain damaged by a misaligned sprocket is not.
Cost, Downtime and a Practical Decision Rule
What a Chain Replacement Really Costs
The chain is usually the largest single line in an undercarriage repair, but it is not the whole cost. Labour to strip and fit the track, the shoes and hardware, any rollers or sprocket segments replaced at the same time, freight for a heavy assembly, and the lost machine days all add up. That ratio is why the cheapest chain on the shelf is poor value: the saving on the part is small against the total job, and an early failure pays the entire labour bill a second time. Downtime carries a further cost when a machine cannot be moved out of a pit or a confined site with a broken track. Weighing the true cost means counting the chain, the matched set, the related wear parts, the labour and the lost production together, rather than comparing two chain prices in isolation. A correctly specified chain fitted with a sound set of rollers and sprockets is almost always the least expensive outcome measured over a season.
The Decision Rule in One Paragraph
The rule is short. Measure the pitch, compare it with the standard, and act on the number. Below one percent, keep running and keep measuring. Between one and two percent, plan and budget. Between two and three percent, order a matched set and check the rollers, sprockets and idler at the same time. Above three percent, stop the machine. Quote the full reference including the suffix, specify the pitch, link width, shoe pattern and sealing type, and buy from a supplier who will confirm fitment against your serial number in writing. Fit the set with correct tension, recheck it after the first hours, and record the baseline measurement. Do that and the track chain stops being a surprise failure and becomes what it should be: a planned, predictable wear item that keeps the machine working and protects every other component in the undercarriage.

